Manuals / SEFL 39859 Parts Book.docx
SOUTHEASTERN FREIGHT · CST20W
SEFL 39859 Parts Book.docx
- Parts
- 74
Parts
74 of 74 parts
| Item | Part No. | Description | Section | Qty |
|---|---|---|---|---|
| — | 15594 | Kit, Eye&Shank, Hex Nut, W/Sfty Wire & Rnd Bush | — | — |
| — | 22018G | Side Channel, 102" Dl, VAII, Galv | — | — |
| — | 22112 | Installation, Limit Cables 16", 86-102Dl VAII | — | — |
| — | 31042-00 | 90° 1/8”MNPT x 1/4”TBG | — | — |
| — | 31083-12 | Drain - Petcock | — | — |
| — | 31083-23 | Control Box Only (without lid) | — | — |
| — | 31083-28 | Control Box Lid w/Screws and Gasket | — | — |
| — | 31084-01 | Bulkhead Fitting | — | — |
| — | 31084-02 | Bulkhead Fitting | — | — |
| — | 31084-10 | Control Box Flow Sensing Switch - In-Line. ThermALERT ready. Color Gray. Replaces 31084-03 which cannot be used on | — | — |
| — | 31114-00 | Steel 1/8” Bulkhead/Check Valve | — | — |
| — | 31114-00 | Control Box Bulkhead/Check Valve | — | — |
| — | 31163-00 | 1/4”TBG Union Tee | — | — |
| — | 31182-70 | Wiring Harness | — | — |
| — | 31222-00 | 1/4” Cable Choke Seal | — | — |
| — | 31272-01 | MTIS Attention Label, 10 pack | — | — |
| — | 31282-01 | MTIS 1-800 Label, 10 pack | — | — |
| — | 31314-21 | 10.50” | — | — |
| — | 31317-03 | 3.50” | — | — |
| — | 31364-00 | 11.50” | — | — |
| — | 31373-00 | 17.00” | — | — |
| — | 31482-01 | 12-R Press Plug O-Ring (328), 3 pack | — | — |
| — | 31492-01 | O-Ring (small 020), 10 pack | — | — |
| — | 31924-03 | Dana/Eaton V3 and V4 | — | — |
| — | 31935-03 | Ingersol F22, Hendrickson HN | — | — |
| — | 31955-03 | Holland ProPar | — | — |
| — | 31964-03 | Meritor TN/TQ, HN, D22 Hollow | — | — |
| — | 31982-01 | Small Parts Assortment. Contains: Pressure Protection Valve, 1/4” NPT x 1/4” TBG 90° Fitting, 3/8” Hex Nipple | — | — |
| — | 32184-01A | TP Press Plug Kit with O-Ring | — | — |
| — | 32184-01A | 2.75” Press Plug Kit with O-Ring. Includes Adhesive. Used in Meritor TP, TB, WP, Hendrickson HP (After 2002) | — | — |
| — | 32202-01A | 1.75” Press Plug Kit with O-Ring | — | — |
| — | 32202-01A | 1.75” Press Plug Kit with O-Ring. Includes adhesive. Used in Meritor TN/TQ, RN/RQ, Hendrickson HN | — | — |
| — | 32251-01 | O-Ring (large 324), 3 pack | — | — |
| — | 32261-00 | MTIS Light Label (Single Pack) | — | — |
| — | 32271-01 | Press Plug Kit with O-Ring. Includes Adhesive. Used in Sudisa 9M Axle | — | — |
| — | 32321-01A | 2.75” Press Plug Kit with O-Ring. Includes Adhesive. Used in Holland ProPar | — | — |
| — | 32321-01A | ProPar Press Plug Kit with O-Ring | — | — |
| — | 32342-01A | 1.904” Press Plug Kit with O-Ring. Includes Adhesive. Used in Holland Trade | — | — |
| — | 32342-01A | 1.86” Holland Trade Press Plug Kit | — | — |
| — | 32352-01 | 1.86” Press Plug O-Ring (223), 3 pack | — | — |
| — | 32375-03 | Holland Trade | — | — |
| — | 32382-01A | 2.95” Press Plug Kit with O-Ring used in Meritor TB Axles with Large Spindle Bore | — | — |
| — | 32382-01A | 2.95” Press Plug Kit with O-Ring. Includes Adhesive. Used in Meritor TB Axles with Large Spindle Bore | — | — |
| — | 32405-03 | Meritor TB (2.95”) | — | — |
| — | 32472-01A | 2.50” Hendrickson HP Press Plug Kit | — | — |
| — | 32473-01A | 2.50” Press Plug Kit with O-Ring. Includes Adhesive. Used in Dana P22, Hendrickson HP (Pre 2002) | — | — |
| — | 32595-03 | Sudisa 12-R | — | — |
| — | 32601-01A | 2.25” Press Plug Kit with O-Ring. Includes Adhesive. Used in Sudisa 12R | — | — |
| — | 32611-01A | 1.50” Press Plug Kit with O-Ring. Includes adhesive. Used in Sudisa 11M | — | — |
| — | 32645-03 | Sudisa 11-M | — | — |
| — | 32701-01A | 1.50” Press Plug Kit with O-Ring. Includes adhesive. Used in Ingersol F22 | — | — |
| — | 32815-03 | Dana P22, Hendrickson HP | — | — |
| — | 36804 | Fastener Kit, Side Channel Replacement, VAII | — | — |
| — | 39326 | DWB KIT 11 X 102 SYSCO, GALVANIZED CS | — | — |
| — | 39327 | DWB KIT 11 X 102 SYSCO, GALVANIZED RS | — | — |
| — | 51011-01 | Driver - Holland ProPar | — | — |
| — | 51011-02 | Driver - Meritor TN/TQ, RN/RQ, Hendrickson HN, Dana/ Eaton D22 Hollow Spindle | — | — |
| — | 51011-03 | Driver - Sudisa 12-R | — | — |
| — | 51011-04 | Driver - Sudisa 11-M | — | — |
| — | 51011-05 | Driver - Holland Trade | — | — |
| — | 51011-06 | Driver - Meritor TP/TB | — | — |
| — | 51011-07 | Driver - Meritor WP | — | — |
| — | 51011-08 | Driver - Ingersol F22 | — | — |
| — | 51011-09 | Driver - Sudisa 9-M | — | — |
| — | 51011-10 | Drive Handle | — | — |
| — | 51011-11 | Driver - Hendrickson ProPar (2.50”) | — | — |
| — | 51011-13 | Driver - Dana P22 | — | — |
| — | 51011-14 | Driver - Meritor TB (2.95” Oversized Bore) | — | — |
| — | 51031-00 | System Pressure Test Gauge. Replaces 81014-00 | — | — |
| — | 61021-01A | Press Plug Kit with O-Ring. Includes Adhesive. Used in Meritor TL Axles | — | — |
| — | 61051-00 | Driver - Meritor TL | — | — |
| — | 81044-00 | Slide Hammer - Removes axle plugs and press | — | — |
| — | 81044-00 | Press Plug Remover. Attaches to 81044-00 | — | — |
| — | 81044-01 | Welsh Plug Removal Spear. Attaches to 81044-00 | — | — |
Service Procedures
1. UNCOUPLING · COUPLING
Pull dolly slowly out from under the trailer.
1. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Set brakes on unit.
1. Drawbar Eye Inspection · COUPLING
Drive Handle and Drivers (for installation of Press Plugs into Axle Spindles)
2. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Remove safety wire on shank nut.
2. UNCOUPLING · COUPLING
If the handle will not pull outward when the vehicle
3. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Remove shank nut and shank washer.
4. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Use forklift for hostler to pull against drawbar
5. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Lubricate the shank of the new drawbar eye with rubber lubricant or soapy
6. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
After the drawbar eye is in place, clean the threads on the shank and coat the
6. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Set the brakes on the trailer. Use a forklift or hostler to push against the
7. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Install the shank washer and thread the shank nut onto the shank.
8. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Tighten the shank nut until three to four threads remain exposed inside the nut.
9. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Install a Silver Eagle safety wire on the shank nut to prevent it from backing off.
10. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL
Periodically check the tightness of the shank nut and adjust as necessary.